空气雾化喷嘴压力传送式喷雾装置（外混式）
雾化喷嘴有点和特性：
通过外部混合装置，无需改变液体流量，只需改变空气压力，即可对雾化进行控制。
对于扇形喷雾，尺寸A，B,和C是距离喷嘴相应距离处的喷雾角度；
Through the external mixing device, without changing the liquid flow, only need to change the air pressure, can to control the atomization.
For the fan-shaped spray, size A, B, and C corresponding distance is the distance the nozzle spray Angle;
The spray from the nozzle to the maximum dispersion point projection a total distance of D;
When using pressure conveying liquid system, liquid by pressure was taken to the nozzle;
Liquid and compressed air or other gas is mixed in the outside, to produce fully atomized spray;
小流量空气雾化喷嘴BIM系列：
产生平均粒径100micron以下之“微雾”的二流体扇形喷嘴；
对喷雾液体加0.1-0.3MAa程度之压力的液体加压式，有很广的流量调整范围；
喷雾角度60°。
产生平均粒径30micron以下之微雾的二流体扇形喷嘴，不需要供给液体加压装置之虹吸式。
一般应用：
散步：脱模机、除臭剂、油、表面处理剂、防锈剂、润滑剂、蜂蜜、防虫剂、尿素水、其他；
冷却：模具、气体、钢板、钢片、铸物、车体、涂装物、玻璃板、塑胶、其他。
调湿：纸、废气、陶瓷、混凝土、其他
洗净：精密基板、玻璃管、其他
Small flow air atomizing nozzle BIM series:
Below the average particle size of 100 micron 'micro fog' two fluid fan nozzle;
To spray liquid pressure of 0.1 to 0.3 degree of MAa liquid pressure type, there is a wide range of flow adjusting range;
The spray Angle 60 °.
Have an average particle size of micro fog two fluid under 30 micron fan nozzle, do not need to supply the siphon type of liquid pressure device.
General application:
Walking: stripper, deodorant, oil, surface treatment agent, anti-rust agent, lubricant, honey, pest control, urea and other water;
Cooling: mold, gas, steel plates, steel sheets, casting material, car body, coating material, glass, plastic and other.
Humidity: paper, waste gas, ceramic, concrete, other
Wash: precision base board, glass tube, the other
带开关控制的空气雾化喷嘴JJAU设计特点
1/8jjau系列喷嘴与1/4JAU系列喷嘴功能是一致的，只是结构上紧凑精巧，适合空间狭小的场合使用。
1/8JJAU系列喷嘴的大的特点是一个内部气体驱动腔，能够控制喷雾的开和关，每分钟*快运行180次。
在喷嘴本体上有一个雾化空气入口AIR和液体入口LIQUID，螺纹接口为1/8，另外针阀驱动腔空气入口为CYL。
喷嘴本体可以与*的迷你型喷雾装置配合使用。
雾化喷嘴一般应用:
磨具自动润滑；
喷雾加湿；
自动喷涂脱膜剂；
自动喷洒；
自动喷码打标；
定时定量喷洒化学剂；
With a switch control air atomizing nozzle JJAU design characteristics
1/8 jjau series nozzle and 1/4 jau series nozzle function is the same, just the structure compact, suitable for occasions in the narrow space.
The biggest characteristic of 1/8 jjau series nozzle is an internal gas driven cavity, can control the spray and off, run the fastest 180 beats per minute.
On the nozzle body has a atomization AIR inlet AIR and LIQUID inlet LIQUID, screw thread interface at 1/8, while needle valve driven cavity AIR inlet for cyl.ul.
Nozzle body can be used with dedicated miniature spray.
Spray nozzle general applications:
Abrasive tool automatic lubrication;
Spray humidification;
Automatic spraying remover;
Automatic spraying;
Automatically printing marking;
Timing quantitative spraying chemical agent;
主营：;欢迎与我们联系！
